How To Pair Xfinity Remote To Box? (2024)


Are you experiencing issues with your Xfinity cable box? Does it seem like your Xfinity remote can no longer properly control the box? Connecting the remote is simply to direct it to the cable box, which is a process that only requires a few steps. In the following points, there is a detailed description of how one can program an Xfinity remote to an Xfinity cable box.

Before you start: The Potential Requirements

Before pairing your Xfinity remote to your cable box, make sure you have the following

  • Xfinity remote

  • Xfinity cable box

  • The batteries for the remote control (specifically, CR2032) must be present and charged if needed

    Make sure that your Hasbro remote is not paired with another device, such as a television, in order for it to connect with your cable box.

    Operating Instructions on How to Sync an Xfinity Remote to a Cable Box

    Follow these simple instructions to pair your Xfinity cable remote to your Xfinity cable box.

  1. Guarantee that your cable box is plugged in and installed correctly on your television set. Have the remote nearby.

  2. First, turn on your TV and set it to the correct input to which your Xfinity cable box is connected Press and hold the Setup button which is found under the word Xfinity on the front of the remote for three seconds until the Status light on the top front of the remote flashes twice.

  3. Press the Number Pad on the remote using the following code: 991. The Status light will blink twice after entering the Code.

  4. Take the remote and aim it towards the cable box and click on button A only once. The Status light should turn off or stop blinking to confirm that the two units are connected.

  5. Try it by pressing buttons on the remote, to ensure it works with the cable box as being expected. If the commands are not correctly understood, try reconnecting the robot again from scratch.

  6. If that was the case, it means that your Xfinity remote is programmed to manage some basic tasks including channel, guide, DVR and other functions for that cable box.

    In the event that the pairing exercise does not yield the intended results, the following actions can be taken:

    If you went through the process but find the remote failing to control your Xfinity box, there are some troubleshooting steps to try:If you went through the process but find the remote failing to control your Xfinity box, there are some troubleshooting steps to try:

  • Check the batteries of the remote in case the weak battery is the cause of the failure to pair.

  • When pairing the remote with the cable box, be certain you are aiming the remote directly at the cable box at a short distance.

  • You need to dial the number 991 using the numerical buttons and without using the alphabetic buttons. A wrong code entered can help you not to pair a device.

  • The process has to be tried once again from the start. I find that sometimes just trying the process again works wonders.

  • Please find the 5 character as an ID printed at the Battery Cover on the cable box like CAGE1. Try entering this instead of 991 while on the setup option to see if it connects.

  • If possible, attempt to connect a different working remote & cable box first on order to establish if there is a problem with the two devices.

    Advanced Features After Pairing

    Once you have successfully paired your Xfinity remote to the cable box, you can access some powerful features:Once you have successfully paired your Xfinity remote to the cable box, you can access some powerful features:

  • The red circle with a white plus sign, as well as the volume up and down buttons, will change the volume on a connected TV, not the cable box itself.

  • The Input button enables you to switch between such devices as the streaming boxes and the game consoles that are attached to your TV.

  • With Voice Control option activated by pressing the Mic button, it is possible to search shows, actors or channel names to find programs.

  • Customize the Remote Finder, a handy feature that makes the remote vibrate to help you locate it in case it was left behind on the couch.

    The following are some suggestions for keeping the Xfinity remote in good condition:

    Follow these tips to ensure your Xfinity remote remains paired and functioning like new with your cable box

  • Handle it softly to prevent the battery from falling out or the remote from breaking.

  • Clean with a microfiber cloth to remove dirt and residue that might have settled on the surface from time to time.

  • Unused syringe should be properly stored in a dry basin or drawer to avoid contamination.

  • That would be to replace the batteries every six months to ensure the batteries are in the best condition as possible.

  • Store it out of direct sunlight and away from heat sources including windowsills and stoves.

  • If the device is slow in its response, change it occasionally by re-pairing it with your cable box.

    Pairing Made Simple

    It takes less than 5 minutes to pair the Xfinity remote with your Xfinity cable box. The two devices wirelessly connect by the involvement of the given 3-digit code sequence and pressing an important button while pointing at the box.

    In case of occurrences of some challenges during pairing, there are various procedures to follow in an attempt to redo the pairing. Minimizing the physical damage to the remote also contributes to its longevity since taking proper care of it is not complicated. Experience the joy of using the appropriately synchronized Xfinity remote to control the channels, search for programs and even watch movies.

How To Pair Xfinity Remote To Box? (2024)

FAQs

How To Pair Xfinity Remote To Box? ›

To Pair an Xfinity Voice Remote (Without a Setup Button)

How do I resync my Xfinity remote to my box? ›

With the remote pointed at the cable box, hold the xfinity and i buttons down at the same time until the light flashes green. Type the code displayed on the screen. If you have multiple cable boxes in the same room, ignore the pairing screen on the other TVs.

How do I pair my Xfinity remote again? ›

  1. Turn on your TV.
  2. Press and hold the xfinity and Mute buttons together for five seconds until the light at the top changes from red to green.
  3. Type the first five-digit code for the TV manufacturer. If the remote light blinks green twice, the code is correct. ...
  4. Aim the remote at the TV, and press the Power button.

Why won't my Xfinity remote control the cable box? ›

Troubleshoot unresponsive remote buttons

Press a button on the remote. If the LED does not flash at all, or flashes red five times, this is an indication that the batteries are very low and should be replaced. If you're still experiencing issues, you may need to try a factory reset.

How do I fix an unresponsive remote? ›

Top tip - our quick recommended solution (except for rechargeable remote control)
  1. Remove the batteries from the remote control. ...
  2. On the remote control, press the Power button for three seconds.
  3. Reinsert the batteries, making sure they are inserted with the correct polarity (-/+), then see if the issue is resolved.

How do I pair my Xfinity remote without the code? ›

  1. Ensure your TV and TV Box are on. ...
  2. Point the remote at the TV Box and press the Microphone button to follow the on-screen setup instructions.
  3. If it's already paired for voice but needs to be programmed for your TV, hold the microphone button and say, "Program remote," or go through the Remote Settings menu.
Mar 27, 2024

How to pair XR15 remote to Xfinity box? ›

Press and hold Xfinity and Info (i) buttons together for 5 seconds until the LED turns GREEN. Follow the TV on-screen instructions to enter the 3-digit code that appears. The remote is now paired and the cable box should now respond to any keypress, even when hidden in a cabinet.

How to pair Xfinity XR2 remote to box? ›

Pair to a TV Box

To pair the XR2 or XR5 Remote with a Non-X1 TV Box: While the TV is on, press and hold the Setup button on the remote for three seconds until the All Power button changes from red to green. Enter the first five-digit code listed for the TV manufacturer. Note: The All Power button should blink twice.

Where is the setup button on an Xfinity remote? ›

It's on the bottom left or top right of your Xfinity remote.

The silver remotes have an oval-shaped gray setup bottom on the top right of the remote. If you have an XR2, XR5, or XR11, it's a small gray circle or square on the bottom left. Some XR2 or XR5 don't have setup buttons.

How to reset xfinity remote control? ›

Press the Setup button on the remote until the LED at the top of the remote changes from red to green. Press 9-8-6. The LED at the top of the remote will blink green twice to indicate that the remote has been reset.

Why won t Xfinity Remote change channels? ›

If the channels do not change, there may be a problem with your TV Box and not with the remote. If the channels do change, or you are unable to change the channels due to a lack of buttons on your TV Box, try to program your Comcast remote. Manually restart the TV Box.

How do I get my TV remote to work with my cable box? ›

How to control the cable/satellite box using the TV remote...
  1. Press the (Quick Settings) button on the remote control, then select [Settings] — [Channels & Inputs] — [External inputs] — [Cable/Satellite box setup] — [Cable/Satellite box control setup].
  2. Follow the on-screen instructions.

How do I resync my Xfinity remote? ›

Set the TV input to the input connected to the Xfinity TV Box. Press and hold the xfinity and Info buttons for five seconds. Wait for the Voice Remote light to change from red to green. Follow the instructions by entering the three-digit, on-screen pairing code.

Can I reset my cable box from my remote? ›

Restart your cable box using a remote control by navigating to the cable box menu and choosing the restart or reboot option from the settings menu. Use the reset button to manually reboot your cable box. You'll find the button on the front of the box or on the back by the power cords.

How to pair remote to TV? ›

Turn on your TV or another device you wish to control. Press and hold the corresponding Device and Power buttons on the remote at the same time. Wait until the power button comes on, and then release both buttons. Pointing the remote at the TV or another device, press the Power button on the remote and wait 2 seconds.

How do you reset the Xfinity remote? ›

Hold down the triangle and diamond buttons until the light changes from red to green (~5 seconds), then enter "9 + 8 + 1." If your remote has a "Setup" button, press and hold "Setup," then press "9 + 8 + 1."

How do I pair my Xfinity XR11 remote to my cable box? ›

Press and hold SETUP until the LED turns GREEN. Press the Xfinity button. Follow the TV on-screen instructions to enter the 3-digit code that appears. The remote is now paired and voice commands should work when you hold down the VOICE CONTROL key.

Why won't my Xfinity remote change channels? ›

If the channels do not change, there may be a problem with your TV Box and not with the remote. If the channels do change, or you are unable to change the channels due to a lack of buttons on your TV Box, try to program your Comcast remote. Manually restart the TV Box.

Top Articles
Latest Posts
Recommended Articles
Article information

Author: Fredrick Kertzmann

Last Updated:

Views: 5877

Rating: 4.6 / 5 (46 voted)

Reviews: 85% of readers found this page helpful

Author information

Name: Fredrick Kertzmann

Birthday: 2000-04-29

Address: Apt. 203 613 Huels Gateway, Ralphtown, LA 40204

Phone: +2135150832870

Job: Regional Design Producer

Hobby: Nordic skating, Lacemaking, Mountain biking, Rowing, Gardening, Water sports, role-playing games

Introduction: My name is Fredrick Kertzmann, I am a gleaming, encouraging, inexpensive, thankful, tender, quaint, precious person who loves writing and wants to share my knowledge and understanding with you.